| SPECIFICATIONS |
| Recording
Module |
| Channel
Setup Features |
|
Calibration — From volts or mm to user defined units |
| |
Ten
built-in Event Marker Text Buffers — Ten user-defined text
buffers for one touch event annotation, plus one "on-the-fly"
marker |
| |
Sample
Rate Range — 0.1 to 25,000 sample/sec, each channel (8-channel)
0.1 to 12,500 sample/sec, each channel (16-channel) |
| |
DSP
Functions — d/dt, Integration, Low Pass Filter, Tachograph |
| |
Recording
Duration — User defined in seconds, minutes, hours or number
of samples |
| Display
Features |
|
Display
— One touch display on/off |
| |
Chart
Speed — 1 mm/hr to 100 mm/sec (simulated) |
| |
Line
Styles — 5 styles |
| |
Color — Any color supported by Windows® |
| |
Values
— Instantaneous values displayed on-screen |
| |
DSP Function Parameters — Modify trigger levels, filter
cutoffs |
| Analysis
Module |
| On-screen
Measurements (uses two on-screen cursors) |
|
Interactive Measurements — delta Y, delta T, 1/delta
T (frequency), slope |
| |
Additional
Calculations — Minimum, maximum, mean, standard deviation,
integral, area, rate, BPM (beats per minute), peak-to-peak value |
| |
Measurements
can be saved to ASCII log file |
| Analysis |
|
Trend
— Mean, min/max, integration (power spectrum) |
| |
FFT
(Spectral Analysis) Windows
a. Window filtering — None (uniform), Hann, Hamming,
Blackman-Harris, Exact Blackman, Blackman, Flat Top, 4 Term B-Harris,
7 Term B-Harris
b. Display Units — Vrms2,
Vpk2, Vrms2/Hz,
Vpk2/Hz
c. Display Type — Linear or logarithmic (dB)
d. Digital Values — Total power, estimated peak power
and estimated peak frequency |
| |
Zoom
a. Filter Types — Low Pass, High Pass, Band Pass, Band
Stop
b. Start/Stop Frequencies — 0.1 Hz to 500 Hz
c. Filter Order — 1 to 10 |
| |
X-Y
Plotter — Plot any channel segment against any other channel |
| Display
Features |
|
Plot
Properties — Color, Pen width, Point style |
| |
DSP
Functions — d/dt, Integration, Low pass filter, Tachograph |
| |
Y-Scale
Control — Autoscale: always, once, never: Manual control:
Log scale on/off |
| |
Scales
— Linear, Log (dB) |
|
| SPECIFICATIONS
(continued) |
| Scope
Mode |
| Four
Channels |
|
Input
Range of ±5 volts |
| |
Maximum
Sample Rate of 50 kHz |
|
Vertical Resolution |
|
16
bits |
|
Trigger |
|
Modes
— Continuous (Auto), Normal, Single |
| |
Source
— External TTL |
| |
Controls
— Level (±5 volts), Rising/Falling Edge |
| Time
Base Range |
|
0.1
ms/div to 100 ms/div |
| Real-time
Computed Math Channels |
|
Channel
1 + Channel 2
Channel 1 - Channel 2
Channel 1 x Channel 2
Channel 1 ÷ Channel 2
Minimum
Maximum
Average: 16, 64 or 256 Sweeps
Envelope |
| Save/Recall
Screen Data to Disk |
|
ASCII
format |
| On-Screen
Cursor Measurements |
|
Time,
voltage, delta T, delta V, minimum, maximum |
| |
| Minimum
Hardware/Software Requirements |
|
• Minimum: Pentium processor
• 256 MBytes of RAM minimum
• 200 MBytes hard disk space
• Windows 2000/XP |
| Recommended
Hardware/Software Requirements |
|
• Recommended: Pentium IV processor
• 512 MBytes of RAM recommended
• 1 GByte hard disk space
• Windows 2000/XP |
| |
| Components
of PolyVIEW System |
•
Software Modules for recording and analyzing data
• Data Aquisition Module (plug-in card)
• BNC Adaptor Module
• Users Manual |
|
